We use cookies to enhance your experience. By continuing to browse this site you agree to our use of cookies. More info.
With carbon dioxide emissions reaching a record high in 2021, clean energy is more crucial than ever. Solar energy is one such fossil-fuel alternative.
Selenium (Se) is a preferable option, according to Chao Chen of the Wuhan National Laboratory for Optoelectronics (WNLO) and School of Optical Electronic Information at Huazhong University of Science and Technology in China, since it is inexpensive, stable, and nontoxic. However, its low melting point and huge bandgap, or the range in which no electronic states may exist, limit its efficacy. Now that Chen and other researchers have overcome these constraints by alloying selenium with tellurium (Te), selenium solar cells are a more tempting option.
The study was published in the Frontiers of Optoelectronics journal.
According to the scientists, the optimal bandgap range for single-junction solar cells is 1–1.5 eV. However, Se’s bandgap is roughly 1.8 eV, making it less than ideal for deployment in solar cells. By combining selenium and tellurium, the scientists were able to tailor the solar cells to the Shockley-Queisser limit, which is the maximum potential efficacy of a single-junction solar cell.
Alloying [selenium] with tellurium, which has the same crystal structure and [has a] narrow bandgap, can tune the bandgap and increase the melting point, thus expanding the absorption spectrum and improving the quality of [the selenium solar cell] films. Therefore Se1-xTex alloy is expected to achieve the improvement of solar cell efficiency.
Chao Chen, Study Corresponding Author and Associate Professor, School of Optical Electronic Information, Huazhong University of Science and Technology
Due to the perfect band alignment and moderate reaction at the interface of the zinc oxide and the selenium/tellurium, the investigators also employed zinc oxide (ZnO) as an electron transport layer in the manufacturing of the solar cells.
Zinc oxide was selected as the electron transport layer, which can slightly react with Se to enhance its interfacial adhesion and to reduce dangling bonds and thus reduce interfacial defects.
Chao Chen, Study Corresponding Author and Associate Professor, School of Optical Electronic Information, Huazhong University of Science and Technology
The use of zinc oxide, together with the scientists’ examination of particular parts of the selenium tellurium solar cells, was one of the innovative features of this study, according to Chen.
The recombination mechanism and defect type of Se1-xTex alloy solar cell were analyzed by characterizations of light intensity dependent current-voltage, capacitance-voltage and temperature dependent admittance, which will help to further optimize the Se1-xTex alloy system.
Chao Chen, Study Corresponding Author and Associate Professor, School of Optical Electronic Information, Huazhong University of Science and Technology
Investigators found that the new material keeps the previously recognized positive attributes of having a large absorption coefficient and being very photoconductive while boosting efficiency in the new selenium tellurium solar cells.
Chen says, “The efficiency of ZnO/Se0.7Te0.3 solar cells has more than doubled after nine months in the air. ZnO/Se0.7Te0.3 [is proven as] a superior junction with energy band matching and tight adhesion, and the efficiency of 1.85% has been achieved preliminarily.”
Scientists are currently striving to enhance the production of solar cells and eventually scale the technique.
Chen adds, “The next step will be to prepare high-quality Se1-xTex alloy films—eliminate holes and vacancy defects and so on—and optimize device structure—adding the hole transport layer and so on—so as to further improve the efficiency of Se1-xTex alloy solar cells and achieve mass production.”
Jiajia Zheng, Yue Lu, Jiayou Xue, and Jiang Tang, all of WNLO and School of Optical and Electronic Information and the China-EU Institute for Clean and Renewable Energy, all at Huazhong University of Science and Technology; Liuchong Fu, Yuming He, Kanghua Li, Yuxuan Liu, and Chong Dong, all of WNLO and School of Optical and Electronic Information at Huazhong University of Science and Technology took part in the study.
The study was funded by the National Natural Science Foundation of China, the Natural Science Foundation of Hubei Province, the Fundamental Research Funds for the Central Universities, the National Key R&D Program of China, and the China Postdoctoral Science Foundation.
Zheng, J., et al. (2022) Fabrication and characterization of ZnO/Se1-xTex solar cells. Frontiers of Optoelectronics. doi.org/10.1007/s12200-022-00040-5.
Source: www.hep.com.cn
Do you have a review, update or anything you would like to add to this news story?
Dave Cist, Roger Roberts and Rob Sommerfeldt
In this interview, AZoM talks to Dave Cist, Roger Roberts, and Rob Sommerfeldt from GSSI about the Pavescan RDM, MDM, and their ground penetrating radar (GPR) capabilities. They also discuss how this can aid the asphalt production and laying processes.
Following the Advanced Materials Show 2022, AZoM spoke with Cameron Day from William Blythe about the broad scope of the company and its goals for the future.
At the Advanced Materials Show 2022, AZoM caught up with the CEO of Cambridge Smart Plastics, Andrew Terentjev. In this interview, we discuss the company's novel technologies and how they could revolutionize how we think about plastics.
The Intelligent Passive Road Sensors (IRS) can accurately detect road temperature, water film height, ice percentage and much more.
The CVD Diamond from Element Six is a high purity synthetic diamond that is used for electronic thermal management.
The Powder Rheology Accessory expands TA Instruments’ Discovery Hybrid Rheometer (DHR) capabilities to powders, enabling characterization of behaviors during storage, dispensing, processing, and end use.
This article provides an end-of-life assessment of lithium-ion batteries, focusing on the recycling of an ever-growing amount of spent Li-Ion batteries in order to work toward a sustainable and circular approach to battery use and reuse.
Corrosion is the degradation of an alloy caused by its exposure to the environment. Corrosion deterioration of metallic alloys exposed to the atmosphere or other adverse conditions is prevented using a variety of techniques.
Due to the ever-increasing demand for energy, the demand for nuclear fuel has also increased, which has further created a significant increase in the requirement for post-irradiation examination (PIE) techniques.
AZoM.com - An AZoNetwork Site
Owned and operated by AZoNetwork, © 2000-2022